Siemens SICAM P 7KG7750 Manual Download Page 141

Page: 141 / 142

8.1 SICAM P 7KG7750

141

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

Isolation Test

8.1.2.2

Mechanical Stress Tests

Norm

IEC 60688

Isolation test acc. to IEC 60688

5 kV; 1.2

Mechanical dynamic stress

Standards

IEC/EN 60255-21
IEC/EN 60068

Vibration, sinusoidal
for stationary application

IEC/EN 60255-21-1 (06.90)
IEC/EN 60068-2-6 (03.95)
Class 1

Vibration, sinusoidal
transport

IEC/EN 60255-21-1 (06.90)
IEC/EN 60068-2-6 (03.95)
Class 1

Vibration on earthquake
for stationary application

IEC/EN 60255-21-3 (06.90)
IEC/EN 60068-2-57 (03.95)
IEC/EN 60068-3-3 (03.95)
Class 1

Shock, for stationary application

IEC/EN 60255-21-2 (06.90)
IEC/EN 60068-2-27 (03.95)
Class 1

Shock, semi-sinusoidal, transport

IEC/EN 60255-21-2 (06.90)
IEC/EN 60068-2-27 (03.95)
Class 1

Bump test (continuous shock), transport

IEC/EN 60255-21-2 (06.90)
IEC/EN 60068-2-29 (03.95)
Class 1

Summary of Contents for SICAM P 7KG7750















































































































































Search results

Summary of Contents for SICAM P 7KG7750

Reviews:

Siemens SICAM P 7KG7750, Manual, Page: 141 / 142

Search results

Summary of Contents for SICAM P 7KG7750

Reviews: