Siemens SICAM P 7KG7750 Manual Download Page 68

Page: 68 / 142

4.4 Basic Settings

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

4.4.4.2

IEC 60870-5-103 Settings

Measuring value range (MV range)

Parameterization of the measuring value range.

Settings:

•

120 %

•

240 %

Transmit Harmonic

Parameterization of the transmission of harmonic values for the harmonics as per
IEC 60870-5-103 protocol.

Settings:

•

yes

Transmit

•

No transmit

Transmit counter values

Parameterization of the transmission of metered values (for power and pulse) as per IEC 60870-
5-103 protocol.

Settings:

•

yes

Transmit

•

No transmit

*MV range: 240%
*Harmonics: no
*Counters: no

<ok
<cancel

Note

The IEC 60870-5-103 parameters

MV range, Transmission of harmonic

and

Transmission of

metered values

are also offered if Modbus has been selected as a protocol. The settings, how-

ever, are then ineffective.

Summary of Contents for SICAM P 7KG7750















































































































































Search results

Summary of Contents for SICAM P 7KG7750

Reviews:

Siemens SICAM P 7KG7750, Manual, Page: 68 / 142

Search results

Summary of Contents for SICAM P 7KG7750

Reviews: