manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 80 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 80

4 

4.12 Overflow of Measured Values

80

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

4.12

Overflow of Measured Values

If the measured values determined in a measurement circuit are higher than the possible values 
of the parameterized measuring range, a value overflow will be displayed. In addition, this value 
overflow is signaled via Modbus or IEC 60870-5-103 protocol.

The overflow is displayed or transmitted if the nominal AC voltage or AC current values are 
exceeded by 20 %.

Presentation of the measured value overflow in the display

An overflow of the measured values AC voltage and AC current, as well as the derived quantities 
such as active power, reactive power, harmonic, power, THD and cos 

φ

 is displayed by ***. The 

energy counting is only stopped, not reset.

Transmission of the measured value overflow using the Modbus protocol

A special Modbus register (register address 40200) has been reserved for the transmission of 
the measured value overflow. For detailed information, please see the 

Powermeter SICAM P - 

Modbus

 manual (order no. E50417-B1076-C241).

Transmission of the measured value overflow using the IEC 60870-5-103 protocol

The measured value overflow is transmitted using the IEC 60870-5-103 protocol. For detailed 
information, see the 

Power Meter SICAM P 7KG7750/55 - Communication Protocol IEC 60870-

5-103

 manual (order no. E50417-B1000-C375).

UL1-N    10.12   kV   
UL2-N    10.34   kV

   

UL3-N   10.42   kV
IL1     245.4   A 
IL2     244.6   A 
IL3     249.4   A 

2/10

AP

<>  Bd/Prm

   
UL1-N    *** 
IL1-N    ***  
PL1-N    *** 
QL1-N    ***   
HUL1-7   ***
HIL1-7   ***

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments