manualshive.com logo in svg

Siemens SENTRON PAC2200CLP, Product Manual, Page: 61 / 130

Share
Download
Siemens SENTRON PAC2200CLP Product Manual Download Page 61

 

PAC2200CLP 
Equipment Manual, 06/2021, L1V30820585B-02 

59

 

  Commissioning

 

6 

6.1

 

Overview 

Prerequisites  

•

 

The device has been installed. 

•

 

The device has been connected in accordance with the possible connection methods. 

Steps for starting up the device  

1.

 

Apply the measuring voltage 

2.

 

Parameterize the device 

3.

 

Check measured values 

 

 

Note 
Check the connections 

Incorrect connection can result in malfunctions and failure of the device. 
Before starting up the PAC2200CLP, check that all the connections have been made correctly. 

 

 

Note 

When performing an insulation test of the entire installation with AC or DC, the device should 

be disconnected before starting the test. 

 

6.2

 

Applying the measuring voltage 

The device is supplied with power via the measuring voltage. 
Please consult the technical data or the type plate for the type and level of the possible 

supply voltage. 
See chapter Connections (Page 41). 

 

 

WARNING 

Do not apply voltage in excess of the rated voltage limit 

Can cause death, serious personal injury, or equipment damage. 

The maximum voltage listed in the technical data and on the rating plate must not be 

exceeded. 

 

Summary of Contents for SENTRON PAC2200CLP



































































































































Reviews:

No comments