manualshive.com logo in svg

Siemens SENTRON PAC2200CLP, Product Manual, Page: 48 / 130

Share
Download
Siemens SENTRON PAC2200CLP Product Manual Download Page 48

Connection 

 

4.4 Connecting the communication cable 

 

PAC2200CLP 

46

 

Equipment Manual, 06/2021, L1V30820585B-02 

4.4

 

Connecting the communication cable 

4.4.1

 

Ethernet communication cable 

Always use a shielded cable for the Ethernet data cable.  
1. Plug the RJ45 cable connector into the RJ45 device socket until the connector engages in 

the socket.  
2. Provide sufficient mechanical strain relief for the Ethernet cable. 
3. Ground the cable shield.   

4.4.2

 

Grounding of the Ethernet cable 

 

 

NOTICE 
The upper limit values will be violated if the cable is not grounded 

Compliance with the technical limit values for noise radiation and noise immunity is only 

guaranteed if the cable is correctly grounded. The operator of the system is responsible for 

ensuring compliance with the statutory limit values (CE mark).  
Make a shield connection as described here. 

 

 

Implementation 

Ground the Ethernet cable in the vicinity of the PAC2200CLP power monitoring device. To do 

this, expose the foil shield of the cable. Connect the exposed shield to a suitable grounding 

point on the control cabinet, preferably a shielding bus. 

 

Summary of Contents for SENTRON PAC2200CLP



































































































































Reviews:

No comments