Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 9

Page: 9 / 132

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Safety notes

2.1

Safety notices

Important notes on using the device

Safety notices on the use of the device

The following safety notices must be adhered to when setting up and operating the device

and during all associated work such as installation, connecting up, replacing devices or

opening the device.

General notices

WARNING

Safety extra low voltage
The SCALANCE X204RNA is designed for operation with Safety Extra-Low Voltage (SELV)

by a Limited Power Source (LPS). (This does not apply to the SCALANCE X204RNA EEC.)
This means that only SELV / LPS complying with IEC 60950 1 / EN 60950 1 / VDE 0805 1

must be connected to the power supply terminals. The power supply unit for the equipment

power supply must comply with NEC Class 2, as described by the National Electrical Code

(r) (ANSI / NFPA 70).
If the equipment is connected to a redundant power supply (two separate power supplies),

both must meet these requirements.

WARNING

The maximum current via the terminals is 10 A. You should therefore include a fuse that

trips at a current higher than 10 A. The fuse must meet the following requirements:



Suitable for 300 VDC / 250 VAC / max. 10 A



Breaking current at least 10 kA



UL/CSA listed (UL 248-1 / CSA 22.2 No. 248.1)

As an alternative, the following requirements:



Breaking current at least 10 kA



Approved in compliance with IEC 60127-1 / EN 60127-1



Breaking characteristics: B or C for a circuit breaker or slow-blow fuse

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands