Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 98

Page: 98 / 132

Functional description and configuration using Web based Management

7.8 The Switch menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

Operating Instructions, , C79000-G8976-C294-03

●

Oversize

Number of frames with a length greater than 1536 bytes.

●

Dropped L2

Number of frames that were discarded at the receiving port due to lack of resources on

the switch.

If you click the "Reset Counters" button, you reset the counters for all ports.

Figure 7-40 Packet Error Statistic

If you click on an entry in the "Port" column, the "Packet Error Statistics graphic" is displayed

for the selected port. You then see a configurable graphical representation of the counter

value.

Graphic representation of the statistics

This page displays the number of bad frames graphically. The display is dependent on the

cause of the error. There is a separate element in the graphic for each of the following

causes of error:
●

Bad Frames

●

CRC

●

Undersize

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands