Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 65

Page: 65 / 132

Functional description and configuration using Web based Management

7.6 The X200 menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Figure 7-16 Fault Mask Link Down Monitoring

Enable Link Down Monitoring

Select the check boxes of the ports whose connection status you want to monitor. If link

monitoring is activated, an error is signaled when there is no valid link at this port because,

for example, the cable is not plugged in or the connected device is turned off.
An error/fault can be signaled in the following ways depending on the configuration of the

SCALANCE X-200RNA: Signaling contact, fault LED, SNMP trap, entry in the log table and

the syslog.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands