Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 51

Page: 51 / 132

Functional description and configuration using Web based Management

7.5 The System menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

7.5.3

System Restart & Defaults

Resetting the settings

In this menu, you will find a button for restarting the SCALANCE X-200RNA as well as

options for resetting the settings of the SCALANCE X-200RNA.

Figure 7-6

System Restart and Defaults

Note
Note the following points about restarting a SCALANCE X-200RNA:



You can only restart the SCALANCE X-200RNA with administrator privileges.



A SCALANCE X-200RNA should only be restarted with the buttons of this menu and not

by a power cycle on the device.



The browser must not be set so that it reloads the page from the server each time the

page is accessed. The updating of the dynamic content of the page is ensured by other

mechanisms. In the Internet Explorer, you can make the appropriate setting in the

Options > Internet Options > General menu in the section Temporary Internet Files with

the Settings button.



Below the text

Check for newer versions of stored pages, the Automatically check box

must be selected.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands