Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 43

Page: 43 / 132

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Functional description and configuration using Web

based Management

7.1

Introduction

To make the best possible use of the technical possibilities of the SCALANCE X-200RNA

devices, you can adapt the configuration of the device to the concrete situation in which it is

used.
Web Based Management (WBM) accesses the configuration of the SCALANCE X-200RNA

using a Web browser. An Ethernet connection to the device is necessary.

NOTICE

To prevent unauthorized access to the SCALANCE X200RNA, there is an automatic logout

after the 15 minutes or after the time configured in the Agent Timeout Configuration menu.

A manual logout is also possible with the appropriate button in the user interface. Exiting

the browser does does not close the session. If the browser is started again within the

timeout, the session continues to be used.

Note
To use SNMP Management and traps, you require a network management station. This

does not ship with IE switches.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands