Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 32

Page: 32 / 132

Installation

5.1 Types of installation

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

Operating Instructions, , C79000-G8976-C294-03

CAUTION

Do not cover the ventilation grilles
During installation, select a mounting position so that the ventilation grilles are always free

to achieve adequate cooling. With normal orientation, the ventilation grilles are on the top,

bottom and sides (X204RNA EEC only) of the housing.

Minimum clearances

If you install the SCALANCE X-200RNA without forced ventilation or cooling, minimum

clearances must be maintained to neighboring devices or the wall of the housing. By keeping

to the minimum clearances, there is then an adequate stream of air for heat dissipation

during operation. Keep to the following minimum clearances to neighboring devices.

Table 5- 1

Minimum clearances when installing in cabinets

Minimum clearance to devices below the X-200RNA

100 mm

Minimum clearance to devices above the X-200RNA

100 mm

Minimum lateral clearance to devices (X204RNA EEC only)

20 mm

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands