Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 8

Page: 8 / 132

Introduction

1.1 Introduction

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

Operating Instructions, , C79000-G8976-C294-03

Finding information

To help you to find the information you require more quickly, the manual includes not only

the table of contents but also the following sections in the Appendix:
●

Index

●

Glossary

Audience

These Operating Instructions are intended for persons commissioning Ethernet networks

with the Parallel Redundancy Protocol (PRP).

Standards and approvals

The devices of the SCALANCE X-200RNA product line meet the requirements for the CE

mark. You will find detailed information in the section "Approvals and markings" in these

operating instructions.

Note
The specified approvals apply only when the corresponding mark is printed on the product.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands