manualshive.com logo in svg

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Share
Download
Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 102

Approvals and marking 

 

8.1 Approvals and marking 

 

SCALANCE X204RNA  SCALANCE X204RNA EEC     (PRP) 

102

 

Operating Instructions,  , C79000-G8976-C294-03 

The product is designed for use in the following areas: 

 

 

Area of application 

RF interference level 

Immunity to interference 

Industry 

EN 61000 6 4: 2007 

EN 61000 6 2: 2005 

 

 

WARNING 

 

Personal injury and damage to property may occur. 
The installation of expansions that are not approved for SIMATIC NET products or their 

target systems may violate the requirements and regulations for safety and electromagnetic 

compatibility. 
Only use expansions that are approved for the system. 

 

●

 

Keep to the installation guidelines 

The product meets the requirements if you adhere to the installation and safety 

instructions contained in this documentation and in the following documentation when 

installing and operating the product. 

●

 

You can always find the latest documentation on the Internet! 

The current descriptions of the currently available products can always be found on the 

Internet under the specified Internet pages: 
–

 

SIMATIC NET Industrial Twisted Pair and Fiber Optic Networks 

(

http://support.automation.siemens.com/WW/view/en/8763736/

) , Manual 

–

 

EMC Installation Guideline 

(

http://support.automation.siemens.com/WW/view/en/60612658

) , Configuration 

manual 

●

 

Working on the product 

To protect the product from electrostatic discharge, personnel must first discharge any 

electrostatic charge from their body before touching the product. 

 

 

Note 
The product was tested with a device that also complies with the standards listed above. 
When operating the product with a device that does not comply with these standards, 

adherence to the corresponding values cannot be guaranteed. 

Explosion protection directive (ATEX) 

The SCALANCE X204RNA device meets the requirements of the EC directive:   

Summary of Contents for SCALANCE X204RNA EEC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands