manualshive.com logo in svg

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Share
Download
Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 103

 

Approvals and marking 

 

8.1 Approvals and marking 

SCALANCE X204RNA  SCALANCE X204RNA EEC     (PRP) 
Operating Instructions,  , C79000-G8976-C294-03 

103

 

94/9/EC (ATEX95) "Equipment and protective systems intended for use in potentially 

explosive atmospheres" 

 

 

Note 
When using (installing) the SCALANCE X204RNA in hazardous area zone 2, make 

absolutely sure that the associated conditions are adhered to. 

 

 
You will find these conditions on the SIMATIC NET Manual Collection. 
●

 

"Approval of SIMATIC/ SIMATIC NET Products for Direct Installation in Ex-Zone 2" 

ATEX code: 
II 3 G Ex nA IIC T4 Gc KEMA 07 ATEX 0145X 
The product meets the requirements of the standards 
●

 

EN 60079-15 (electrical apparatus for potentially explosive atmospheres; Type of 

protection "n") 

●

 

and EN 60079-0 

FM approval 

The SCALANCE X204RNA meets the requirements of the standards:   
●

 

Factory Mutual Approval Standard Class Number 3611 

●

 

FM Hazardous (Classified) Location Electrical Equipment: 

Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 A and 

Non Incendive / Class I / Zone 2 / Group IIC / T4 

FDA and IEC approvals 

The following products meet the FDA and IEC requirements listed below. 
●

 

SFP module SFP991-1LD 

●

 

SFP module SFP991-1LH+ 

 

Figure 8-1 

FDA and IEC approvals 

Notice for Australia (C-Tick) 

The product meets the requirements of the AS/NZS 2064 standard (Class A).   

Summary of Contents for SCALANCE X204RNA EEC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands