Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 11

Page: 11 / 132

Safety notes

2.1 Safety notices

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

WARNING

Suitable cables for temperatures in excess of 70 °C
If the cable or conduit entry point exceeds 70°C or the branching point of conductors

exceeds 80°C, special precautions must be taken. If the equipment is operated in an air

ambient in excess of 50 °C to 70 °C, only use cables with admitted maximum operating

temperature of at least 80 °C.

WARNING

Protection against transient voltage surges
Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

Safety requirements 100 to 240 VAC (SCALANCE X204RNA EEC only)

Safety requirements for installation
According to the IEC 61131-2 standard and therefore in accordance with the EU directive

2006/95/EC (Low Voltage Directive), the devices are "open equipment" and in accordance

with UL/CSA certification, they are an "open type".
To fulfill requirements for safe operation with regard to mechanical stability, flame

retardation, stability, and shock-hazard protection, the following alternative types of

installation are specified:
●

Installation in a suitable cabinet.

●

Installation in a suitable enclosure.

●

Installation in a suitably equipped, enclosed control room.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands