Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 57

Page: 57 / 132

Functional description and configuration using Web based Management

7.5 The System menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

7.5.7

System Select/Set Button

Configuring the Select/Set button

On the SCALANCE X-200RNA, the SELECT/SET button is used to
●

Change the display mode

●

Reset to the factory defaults

●

Define the fault mask and the LED display

You will find a detailed description of the individual functions available with the button in the

section "Set button (Page 27)".
On this page, the functionality of the Select/Set button can be restricted or fully disabled.

This is possible for the following three functionalities:
●

Restore Factory Defaults

●

Enable/Disable Reset

●

Set Fault Mask

Figure 7-10 Select/Set button configuration

Enable Select/Set Functions

You can enable or disable the individual functions of the button by checking or unchecking

the relevant box.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands