Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 124

Page: 124 / 132

Glossary

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

124

Operating Instructions, , C79000-G8976-C294-03

Default gateway

A network node that forwards all frames not addressed to stations in the same LAN (subnet).

DHCP

DHCP (Dynamic Host Configuration Protocol), like BOOTP, a method for automatic

assignment of IP addresses. However, with DHCP, addresses can also be assigned while

the device is running.

Event

for Alarms & Events: An event is any occurrence that might be of interest to the client.

Although events can also be generated due to a condition being met, they do not need to be

related to conditions. Events that are not related to conditions include, for example, error

messages from the communications system.

Fault mask

Specifies the desired status (good status). Deviations from this occurring during operation

are handled as faults.

High Speed Redundancy

Method used on SIMATIC NET switches to increase the network availability in a ring

topology.
See also ►Media redundancy.

HTTP

Hypertext Transfer Protocol.
Protocol for transfer from Web sites

Media redundancy

Method for increasing availability in Industrial Ethernet networks in which devices can be

reached over different paths. This might be achieved by meshing networks, arranging

parallel transmission paths or by closing a linear bus topology to form a ring.
Media redundancy within a ring topology is available with SIMATIC NET products with the

►High Speed Redundancy and ►MRP methods.

Media Redundancy Protocol

A method specified in the IEC 61158 Type 10 standard for increasing network availability in

a ring topology.
See also ►Media redundancy.

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands