Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 36

Page: 36 / 132

Installation

5.3 Wall mounting

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

Operating Instructions, , C79000-G8976-C294-03

5.3

Wall mounting

Wall mounting of a SCALANCE X204RNA

Preparation for wall mounting

Wall mounting

For wall mounting, use suitable mounting fittings for the wall (for example, for a concrete

wall, two plugs 6 mm diameter and 30 mm long, 2 screws 3.5 mm diameter and 40 mm

long).

Connect the electrical cable connecting cables.

Fit the connectors for the signaling contact.

Insert the terminal blocks into the sockets on the SCALANCE X204RNA.

For more exact dimensions, please refer to the section "Dimension drawings" (Page 119) in

the manual.

Note
The wall mounting must be capable of supporting at least four times the weight of the

SCALANCE X204RNA (see "Technical specifications").

Wall mounting of a SCALANCE X204RNA EEC

To mount the SCALANCE X-204RNA EEC on a wall, secure an adequately long piece of

DIN rail (35 mm) to the wall. For wall mounting, use suitable mounting fittings for the wall (for

example, for a concrete wall, two plugs 6 mm diameter and 30 mm long, 2 screws 3.5 mm

diameter and 40 mm long).
Now mount the SCALANCE X-204RNA on the DIN rail as described in the section "DIN rail

mounting" (Page 33).

Summary of Contents for SCALANCE X204RNA EEC





































































































































Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands

Siemens SCALANCE X204RNA EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X204RNA EEC

Reviews:

Related manuals for SCALANCE X204RNA EEC

Brands by name

Popular brands