Siemens SCALANCE X204RNA EEC Operating Instructions Manual Download Page 26 | Manualshive

Page: 26 / 132

background image

Product characteristics

4.6 C-PLUG

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

26

Operating Instructions, , C79000-G8976-C294-03

Diagnostics

Inserting a C-PLUG that does not contain the configuration of a compatible device type or

general malfunctions of the C-PLUG are signaled by the diagnostics mechanisms of the

SCALANCE X-200RNA (LEDs, SNMP, WBM, etc.).

Inserting in the C-PLUG slot

The C-PLUG is not supplied with the SCALANCE X-200RNA. It is available as an optional

accessory.
The slot for the C-PLUG is located as follows:
●With a SCALANCE X204RNA on the front of the device
●With the SCALANCE X204RNA EEC on the top of the device
Refer to Figure 4-6 Position of the C-PLUG and SET button (Page 28)

To insert the C-PLUG, remove the protective cover. The C-PLUG is inserted in the slot.
The protective cover must then be closed correctly.

NOTICE

The C-PLUG may only be inserted or removed when the power is off!

Removing the C-PLUG

It is only necessary to remove the C-PLUG if a fault occurs on the SCALANCE X-200RNA.
The C-PLUG can be removed from the slot using flat pliers, tweezers, or a small screwdriver.

See also

SET button (Page 27)

«
...
24
25
26
27
28
...
»

Summary of Contents for SCALANCE X204RNA EEC





































































































































Reviews:

No comments

Related manuals for SCALANCE X204RNA EEC

Brand: D-Link Pages: 17

EtherDevice EDS-4009 Series

Brand: Moxa Technologies Pages: 18

Brand: TP-Link Pages: 2

Brand: Thinklogical Pages: 27

Brand: Kramer Pages: 2

SmartSTACK ETHERNET ELS10-27

Brand: Cabletron Systems Pages: 126

Instant On 1930 Series

Brand: Aruba Pages: 8

Brand: Inter-m Pages: 12

Brand: 3Com Pages: 74

Brand: nedis Pages: 24

Brand: WilTec Pages: 7

Brand: Gefen Pages: 12

iConverter GX/X

Brand: Omnitron Systems Technology Pages: 2

Brand: Fastcabling Pages: 4

Brand: CTC Union Pages: 14

Brand: Blagdon Pages: 6

Digi-Touch DDN-SW1

Brand: Blueridge Pages: 13

Brand: Rosewill Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands