manualshive.com logo in svg

Siemens SAB 80515 Series, User Manual, Page: 244 / 270

Share
Download
Siemens SAB 80515 Series User Manual Download Page 244

Device Specifications

Semiconductor Group

244

If the power-down mode and the idle mode are set at the same time, power-down takes prece-
dence.
Furthermore, register PCON contains two general purpose flags. For example, the flag bits 
GF0 and GF1 can be used to give an indication if an interrupt occurred during normal operation 
or during an idle. Then an instruction that activates Idle can also set one or both flag bits. When 
idle is terminated by an interrupt, the interrupt service routine can examine the flag bits.
The reset value of PCON is 000X0000

B

.

                     

Idle Mode

In the idle mode the oscillator of the SAB 80C515 continues to run, but the CPU is gated off 
from the clock signal. However, the interrupt system, the serial port, the A/D converter, and all 
timers with the exception of the watchdog timer are further provided with the clock. The CPU 
status is preserved in its entirety: the stack pointer, program counter, program status word, 
accumulator, and all other registers maintain their data during idle mode.

The reduction of power consumption, which can be achieved by this feature depends on the 
number of peripherals running.

Table 4
SFR PCON (87

H

)

SMOD

PDS

IDLS

– GF1

GF0

PDE

IDLE

87

H

7

6

5

4

3

2

1

0

Symbol

Position

Function

SMOD

PDS

IDLS

– 

GF1

GF0

PDE

IDLE

PCON.7

PCON.6

PCON.5

PCON.4

PCON.3

PCON.2

PCON.1

PCON.0

When set, the baud rate of the serial channel in mode 1, 2, 
3 is doubled.

Power-down start bit. The instruction that sets the PDS flag 
bit is the last instruction before entering the power-down 
mode.

Idle start bit. The instruction that sets the IDLS flag bit is the 
last instruction before entering the idle mode.

Reserved

General purpose flag

General purpose flag

Power-down enable bit. When set, starting of the power-
down mode is enabled.

Idle mode enable bit. When set, starting of the idle mode is 
enabled.

*

Summary of Contents for SAB 80515 Series















































































































































































































































































Reviews:

No comments