manualshive.com logo in svg

Siemens SAB 80515 Series, User Manual, Page: 158 / 270

Share
Download
Siemens SAB 80515 Series User Manual Download Page 158

Semiconductor Group

158

Instruction Set

DJNZ

<byte>, < rel-addr>

Function:

Decrement and jump if not zero

Description:

DJNZ decrements the location indicated by 1, and branches to the address 
indicated by the second operand if the resulting value is not zero. An original value 
of 00H will underflow to 0FFH. No flags are affected. The branch destination would 
be computed by adding the signed relative-displacement value in the last instruction 
byte to the PC, after incrementing the PC to the first byte of the following instruction.

The location decremented may be a register or directly addressed byte.

Note:

When this instruction is used to modify an output port, the value used as the original 
port data will be read from the output data latch, not the input pins.

Example:

Internal RAM locations 40H, 50H, and 60H contain the values, 01H, 70H, and 15H, 
respectively. The instruction sequence

DJNZ 40H,LABEL_1
DJNZ 50H,LABEL_2
DJNZ 60H,LABEL_3
will cause a jump to the instruction at label LABEL_2 with the values 00H, 6FH, and 
15H in the three RAM locations. The first jump was 

not

 taken because the result was 

zero.

This instruction provides a simple way of executing a program loop a given number 
of times, or for adding a moderate time delay (from 2 to 512 machine cycles) with a 
single instruction. The instruction sequence

MOV

R2, #8

TOGGLE: CPL

P1.7

DJNZ

R2,TOGGLE

will toggle P1.7 eight times, causing four output pulses to appear at bit 7 of output 
port 1. Each pulse will last three machine cycles; two for DJNZ and one to alter the 
pin.

*

Summary of Contents for SAB 80515 Series















































































































































































































































































Reviews:

No comments