Sewha si 4500 Operation Manual Download

Page: 7 / 52

DIGITAL WEIGHING INDICATOR

SI 4500

- 7 -

3-5-1. Status Lamp (ANNUNCIATORS) : “

▼

” Lamp is “ON”.

3-5-2. Key Operation

Make Weight value as Zero.

Under F08, you can set the Zero key operation range, as 2%, or 5%, or 10%, or 20% of

Max. Capacity.

※

Under “Tare” key input, Zero key will not be activated.

Make Weight value as Zero, including Tare Weight.

Under F09, you can set the Tare key operation range, as 10%, 20%, 50%, or 100% of Max.

Capacity.

TARE RESET :

Initialize Batch Process.

If the Batch process is not initialized, the process will not activated.

1. To START or STOP weighing process.

First input, SI 4500 Controller Starts weighing process, and Second input, SI 4500

Controller stops weighing process.

Steady

When the weight is Steady, “

▼

” Lamp is turn on.

Zero

When the current weight is Zero, “

▼

” Lamp is turn on.

(Displayed weight is Zero, “

▼

” Lamp is turn on.)

Tare

Tare function is set, “

▼

” Lamp is turn on.

(Tare Reset

“

▼

” Lamp is turn off.)

STB

Batch “Stand by” display.

Run

Weighing Batch is started, “

▼

” Lamp is turn on.

Print

When print key input or Auto print, “

▼

” Lamp is turn on.

Comm.

When indicator transfers or receives data from other devices, “

▼

” Lamp is turn on. (If the

“

▼

” is off although there is some data transference, please check communication settings).

Summary of Contents for si 4500





















































Search results

Summary of Contents for si 4500

Reviews:

Related manuals for si 4500

Brands by name

Popular brands

Sewha si 4500, Operation Manual

Search results

Summary of Contents for si 4500

Reviews:

Related manuals for si 4500

Brands by name

Popular brands