Sewha si 4500 Operation Manual Download Page 25

Page: 25 / 52

DIGITAL WEIGHING INDICATOR

SI 4500

- 25 -

5-5 F-Function Detailed information

■

General Function Setting

(

●

Factory default set value)

Weighing Data Save Method Selection

(Apply on Accumulated weighing count/weight)

F01

●

Manual Save Mode (Save when “Print” key input)

Automatic Save Mode(Save when Batch Finished)

Weight-Back up selection

F02

●

Normal Mode

Weight Back up Mode

Motion Band Range setting

F03

∫

This is set “Steady” acceptable range of weighing part.

If there is vibration on weighing part, you can set this function and reduce the

vibration effect on weighing process.

1 : Weak vibration

∫

50 : Strong Vibration

Zero Tracking Compensation Range setting

F04

∫

Due to external causes(Temperature, wind, and dust), there are small weight

difference, indicator will ignore the weight difference and display Zero.

For this compensation function, indicator will estimate the weight difference is

over the set range during fixed time period.

If there is large weight difference over set range within fixed time period, the

“Zero” is breaking and will find new zero point.

Auto Zero Range setting

F05

∫

Within the “Auto Zero” range, weighing part is steady, indicator will display

current weight as “Zero”

If the weighing part is not “Steady”, indicator will display current weight.

(Auto Zero Range : ± Set value + weight unit)

Summary of Contents for si 4500





















































Search results

Summary of Contents for si 4500

Reviews:

Brands by name

Popular brands

Sewha si 4500, Operation Manual

Search results

Summary of Contents for si 4500

Reviews:

Brands by name

Popular brands