Sewha si 4500 Operation Manual Download

Page: 42 / 52

DIGITAL WEIGHING INDICATOR

SI 4500

- 51 -

6-5. Analog Output Interface (Option 03 : 4~20mA Output)

This Option card converts weight value to Analog Electric Current output(4~20mA) and transfers to

external devices(Recorder, P.L.C), controlled by electric current output.

6-5-1. Specification

①

. Output Current : 4~20mA (Output Range : 2~22mA)

②

. Accuracy : More than 1/1,000

③

. Temperature Co-efficiency : 0.01%

℃

. Max. Loaded Impedance : Max. 500

Ω

④

When Weight display is “Zero”, 4mA current will be output, when Weight display is “Full

※

Capacity”, 20mA current will be output.

6-5-2. Circuit

“LO” terminal is not a “GND”, so this

※

“LO” terminal do not be connected with

other “GND” terminal on other devices.

6-5-3. Output Adjustment

①

. This output is adjusted as when the weight is “Zero”, output is “4mA” and When the

weight is “Full capacity”, output is “20mA”.

②

. If you need additional adjustment, please adjust with “VR1(Zero)”, “VR2(Span) on the

Analog Output PCB.

Remark

※

This Analog option card converts Displayed weight value(Micro-process data) to analog

value on D/A Converter(Digital to Analog converter)

This D/A Converter has Max. 1/4,000 accuracy, so this output is not suitable for high

accuracy application, like more than 1/3,000.

6-5-4. Connecter (9pin, “D-type” female)

1 : HI(+), 5 : (-)

Summary of Contents for si 4500





















































Search results

Summary of Contents for si 4500

Reviews:

Related manuals for si 4500

Brands by name

Popular brands

Sewha si 4500, Operation Manual

Search results

Summary of Contents for si 4500

Reviews:

Related manuals for si 4500

Brands by name

Popular brands