background image

PRODUCT OPERATION & MAINTENANCE PROCEDURE

 

Model 0101

 

 

 

15

 

POP-0011– Rev. 5 

 

Removing the HDD Anvil 

 
The following is a list of tools required to complete this job: 

 

7/8" Open-End Wrench 

 

1-1/2" Open-End Wrench (Newer Anvils) 

 

1-1/4" Open-End Wrench (Older Anvils) 

 

1.

 

Unplug the power cord from the electrical outlet. 
 

2.

 

Open the access door.  Using either the 1-1/4" or 1-1/2" Open-End Wrench depending upon the Anvil 
installed, place the Open-End Wrench onto the Anvil and turn both the Anvil and hydraulic ram shaft 
until the two flat edges on the hydraulic ram shaft are perpendicular to the door opening.  This will then 
allow the 7/8" Open-End Wrench to slide onto the flats of the hydraulic ram shaft.  See pictures below.  

 

 

 

 

   

 

 
 
 
 

3.

 

Pull Open-End Wrenches apart to loosen. 

 

4.

 

Once loosened unscrew the HDD Anvil from the hydraulic ram shaft by hand. 

 
 
 
 
 
 
 
 
 

Installing the HDD Anvil 

 

1.

 

Place the wedge lock washer over the threaded portion of the HDD Anvil to be installed; then screw the 
HDD Anvil into the bottom of the hydraulic ram shaft until the wedge lock washer touches the base of 
the hydraulic ram shaft.  

Note: Do not tighten the anvil by hand once the lock washer touches the 

base of the hydraulic ram shaft.

 

 

Turn Anvil with 1-1/4" or  

1-1/2" Open-End Wrench

 

Align both wrenches 

as shown 

Summary of Contents for 0101




























Reviews: