Schilling Megalight Manual Download Page 56

Page: 56 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

R.F. Connector

Pin N°

Signal

Description

Status

--------

-------------------------

-----------------

Not used in this version

---------

-------------------------

-----------------

Not used in this version

Wiring diagrams

The Manufacturer agrees to supply upon request the circuit diagrams, lists of component parts,

calibration instructions or other information useful for adequately qualified personnel to repair
the parts of the device which the Manufacturer considers repairable.

The following diagrams are supplied:

•

Rack interface wiring diagram.

•

Interface signal timing diagram.

•

Laser command signal timing diagram.

•

Wiring diagram of DSP2 (optional) command signals.

•

Interface wiring diagram for the DSP2 (optional) board I/O module.

Summary of Contents for Megalight


































































Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands

Schilling Megalight, Manual

Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands