Schilling Megalight Manual Download Page 27 | Manualshive

Page: 27 / 65

background image

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

27

Edition 2004

N.B.: the connectors (11) RF and (9) SLAVE OUT are not used in the Megalight™ engraving
system.

N.B.: It is possible to connect all the devices aimed at making the laser source safe in series

with EXTERNAL INTERLOCK connector (5).

For detailed wiring and connection diagrams, see Appendix B. Wiring and connection diagrams.

Optical fiber connection.

The optical fibre is connected between the laser opening of the power supply box (connector
10: OPTICAL FIBER) and the optical fibre connector socket on the rear wall of the Resonator.

Picture 11: Optical Fibre Connection

The procedure to connect the optical fibre to the rack is as follows:

1.

Make sure the main switch MS is in the OFF position (O ).

WARNING:

Laser radiation may leak from the OPTICAL FIBER connector (10) of the power
supply box. Never work with the device power on. Working with the device

power on may cause serious optical risk.

«
...
25
26
27
28
29
...
»

Summary of Contents for Megalight


































































Reviews:

No comments

Related manuals for Megalight

Brand: VEE GEE Pages: 2

WJ-NU301K Series

Brand: i-PRO Pages: 24

WJ-NU101K Series

Brand: i-PRO Pages: 18

Brand: Vectronics Pages: 4

FLEXFLO M4 Series

Brand: Blue-White Pages: 64

Brand: Ecolab Pages: 95

Brand: Lutron Electronics Pages: 13

Brand: Isspro Pages: 2

Brand: DAKOTA ULTRASONICS Pages: 51

Brand: ATI Technologies Pages: 4

OIL INTENSIFIER SYSTEM

Brand: DH Instruments Pages: 2

Brand: PCE Americas Pages: 111

Brand: SBS Pages: 59

Brand: ZyAura Pages: 2

Brand: Keysight Pages: 896

Brand: SAGE Analytics Pages: 2

VPFlowScope VPS.R01K.M200 series

Brand: VPInstruments Pages: 33

Brand: KABI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands