Schilling Megalight Manual Download Page 40

Page: 40 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

Check for the presence of the signal
(10V)

(pin 3 -1 of the PC connector)

Replace the DSP board in the P.C.
Check the connection wire between the

rack and Resonator

7) No aiming red laser

           -Display signals READY
           -Status led Orange

No power

Replace the DL connection wire

Make sure the cooling air circulates
freely
Make sure the fans are running correctly
Check the ambient temperature

( max.35 °C )
Turn the switch to OFF, wait 10s and turn
to ON.

8.a) The laser stops emitting
-Display in alarm

-Status led Green

Temperature protection tripped
with presence of Alarm

“MAX TEMPERATURE ALARM”

Contact the Call Centre
Make sure the cooling air circulates
freely
Make sure the fans are running correctly

8.b) The laser stops emitting
-Display in alarm

-Status led Green

Temperature protection tripped
with presence of Alarm

“M/S HIGH DIODE TEMP”

Make sure the radiator is clean
Make sure the cooling air circulates

freely
Make sure the fans are running correctly

8.c) The laser stops emitting

           -Display in alarm
           -Status led Green

Temperature protection tripped

with presence of Alarm
“M/S INCORRECT DIODE TEMP”

Make sure the ambient temperature is
above 5 °C and below 35°C
Check the output optical power

9) Laser emission is irregular

           -Display signals READY
           -Status led Red

Variation of the output optical

power

Check the level signal

Check the hours of operation

10) Laser emission is low

           -Display signals READY
           -Status led Red

Decrease of the output optical

power

Contact the Call Centre

Check the connections of the TS and STS
wires

11) The scanner head does not
work

No power or no signal

Replace the DSP board

Summary of Contents for Megalight


































































Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands

Schilling Megalight, Manual

Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands