Schilling Megalight Manual Download Page 11

Page: 11 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

Composition

The Megalight™ device in its basic “O.E.M.” version is composed of:

•

A power supply Rack containing the pump laser diode

•

A compact laser Resonator, designed to take up little room.

•

A connection Optical fibre

The components required to create the “Marker” set-up can be supplied separately as an

option:

•

Engraving scanner head

•

Interfacing electronic boards and engraving software (Windows-based)

•

A Personal Computer with Monitor, keyboard and mouse.

All engraving operations can be managed with the Smartist 4 software program.
(the minimum Personal Computer requirements and Software operating instruction are

provided in the Smartist4 Manual).

The pictures below show the composition of an engraving system and the Megalight™ with

Miniscanner model

Picture 1: Megalight™ engraving laser system

MONITOR

MOUSE AND
KEYBOARD

PERSONAL
COMPUTER

LASER ENGRAVING
HEAD

LASER RACK

Summary of Contents for Megalight


































































Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands

Schilling Megalight, Manual

Search results

Summary of Contents for Megalight

Reviews:

Related manuals for Megalight

Brands by name

Popular brands