Sanav MU-201 User Manual Download Page 57

Page: 57 / 68

MU-201 GPS/GPRS Nano Tracker User Manual

Request Battery Voltage

User can check the current battery voltage of the device by sending the following command:

Command: #battery*

Note: For the example from Message Reply, we found that there are 2 voltage measurements: 3.826V and 3.793V. The

voltage shown will be different because 3.826V is “detected” voltage and 3.793V is instantaneous voltage when sending

the message (the voltage will be dropped a little for a while when sending). So 3.826V will be more precise measurement.

SMS/ COTA Command

Description

Start sign.

battery

Mode “battery” defines Battery Check mode.

End sign

Table: Battery Voltage Check Format Description

Situation

Message Reply

Setup Succeeds

<OK>Vol=V3.826;ADC=688.500000, V3.793;56%

Table: Battery Voltage Check Response Description

Summary of Contents for MU-201




































































Search results

Summary of Contents for MU-201

Reviews:

Related manuals for MU-201

Brands by name

Popular brands

Sanav MU-201, User Manual

Search results

Summary of Contents for MU-201

Reviews:

Related manuals for MU-201

Brands by name

Popular brands