manualshive.com logo in svg

Samsung S3C2501X, User Manual

Share
Download
Samsung S3C2501X User Manual Download Page 81

PROGRAMMER

′′

S MODEL

S3C2501X

2-22

2.16.1.2 Register 0: Cache type

This is a read-only register which allows operating systems to establish how to perform operations such as cache
cleaning and lockdown. Future ARM cached processors will contain this register, allowing RTOS vendors to
produce future-proof versions of their operating systems.

The cache type register is accessed by reading CP15 register 0 with the opcode_2 field set to 1. For example:

MRC p15, 0, rd, c0, c0, 1; returns Cache type register

The register contains information about the size and architecture of the caches. The format of the register is
shown in Table 2-7.

Table 2-7. Cache Type Register Format

Register Bits

Meaning

Value

31:29

Reserved

000

28:25

Cache type

0111

24

Harvard/Unified

1 (defines Harvard cache)

23:21

Reserved

000

20:18

DCache size

011 (defines 4KB)

17:15

DCache associativity

110 (defines 64 way)

14

DCache base size

0 (defines 1x base parameters)

13:12

DCache words per line

01 (defines 4 words per line)

11:9

Reserved

000

8:6

ICache size

011 (defines 4KB)

5:3

ICache Associativity

110 (defines 64 way)

2

ICache base size

0 (defines 1x base parameters)

1:0

ICache words per line

01 (defines 4 words per line)

Summary of Contents for S3C2501X


















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands