manualshive.com logo in svg

Samsung S3C2501X, User Manual

Share
Download
Samsung S3C2501X User Manual Download Page 304

S3C2501X

ETHERNET CONTROLLER

7-15

7.4.1 BDMA RELATIVE SPECIAL REGISTER

7.4.1.1 Buffered DMA Transmit Control Register

Table 7-4. BDMATXCON Register

Registers

Address

R/W

Description

Reset Value

BDMATXCONA

0xF00A0000

R/W

Buffered DMA transmit control register

0x00000000

BDMATXCONB

0xF00C0000

R/W

Buffered DMA transmit control register

0x00000000

Bit Number

Bit Name

Description

[3:0]

BDMA Tx Number of Buffer

Descriptor (BTxNBD)

You can select number of buffer descriptor.

0000 = 2

0

, 0001 = 2

1

, 0010 = 2

2

,….., 11xx = 2

12

[6:4]

BDMA transmit to MAC Tx
start level (BTxMSL)

These bits determine when to move the data of the new frame in
the BDMA Tx Buffer (BTxBUFF) to the MAC TxFIFO (MTxFIFO)
at a new frame arrival.
000 means no wait, 001 means wait to fill 1/8 of the BDMA Tx
Buffer, 010 means wait to fill 2/8 of the buffer, and so on through
100, which means wait to fill 4/8 of the BDMA Tx Buffer.

NOTE:

    If the last data of the frame arrives in BDMA Tx Buffer,

               the data transfer from the BDMA Tx Buffer to the MAC
               TxFIFO starts immediately, regardless of the level of
               these bits.

[8:7]

Reserved

Not applicable.

[9]

–

Factorial test bit

[10]

BDMA Tx enable (BTxEn)

When the Tx enable bit is set to  ‘1’, the BDMA Tx block is
enabled. Even if this bit is disabled, buffer data will be moved to
the MAC TxFIFO until the BDMA TxBUFF underflows.

This bit is automatically cleared when the BDMA is not the owner.

NOTE:

    The BDMATXDPTR register must be assigned before this

                bit is set.

[11]

BDMA Tx reset (BTxRS)

Set this bit to  ‘1’  to reset the BDMA Tx block.

[31:12]

Reserved

Summary of Contents for S3C2501X


















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands