manualshive.com logo in svg

Samsung S3C2501X, User Manual

Share
Download
Samsung S3C2501X User Manual Download Page 279

I

2

C CONTROLLER

S3C2501X

6-4

Start

Condition

Address

P

9

Stop

Condition

SDA by

Receiver

SCL from

Master

8

9

8

R/W

ACK

ACK

S

SDA by

Transmitter

MSB

Acknowledge

from receiver

Acknowledge from

transmitter

2

1

MSB

Data

2

1

Figure 6-3. Master Receiver and Slave Transmitter

Even in this case, the master IC generates the timing and terminates the transfer.

The master IC is always responsible for generating the clock signals on the I

2

C. Bus clock signals from a master

can only be altered by 1) a slow slave IC which "stretches" the signal by temporarily holding the clock line Low, or
2) by another master IC during arbitration.

6.4.2 GENERAL CHARACTERISTICS

Both SDA and SCL are bi-directional lines which are connected to a positive supply voltage through a pull-up
resistor.

When the I

2

C is free, the SDA and SCL lines are both high level. The output stages of I

2

C interfaces connected

to the bus have an open-drain or open-collector to perform the wired-AND function. Data on the I

2

C can be

transferred at a rate up to 100 Kbits/s. The number of interfaces that can be connected to the bus is solely
dependent on the limiting bus capacitance of 400 pF.

6.4.3 BIT TRANSFERS

Due to the variety of different IC's (CMOS, NMOS, and I2L, for example) which can be connected to the I

2

C, the

levels of logic zero (low) and logic one (high) are not fixed and depend on the associated level of V

DD

. One clock

pulse is generated for each data bit that is transferred.

Summary of Contents for S3C2501X


















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands