background image

85

ENGLISH

Grounding work

Grounding must be done by a qualified installer for your safety .

Grounding the power cable

X

f

The standard of grounding may vary according to the rated voltage and installation place of the air conditioner .

X

f

Ground the power cable according to the following table .

Power condition

Installation place

Voltage to ground is lower than 150V

Voltage to ground is over 150V

High humidity

Must perform the grounding work 3 . 

Note 1)

(Including the case where earth leakage breaker is installed)

Average humidity

Perform grounding work 3 . 

Note 1)

Must perform the grounding work 

3 . 

Note 1)

(Including the case where earth leakage 

breaker is installed)

Low humidity

Perform grounding work 3, if possible, 

for your safety . 

Note 2)

Note 1) About grounding work 3.

•  Grounding work must be done by an expert (with qualification) .
•  Check if the grounding resistance is lower than 100Ω . When installing a earth leakage breaker (that can cut the 

electric circuit within 0 .5 second in case of a short circuit), allowable grounding resistance should be 30~500Ω .

Note 2) Grounding at dry place

•  The grounding resistance should be lower than 100Ω . Even in worst case, grounding resistance should be lower 

than 250Ω .

Performing the grounding work

X

f

Use a rated grounding cable by referring to the specification of the electric cable for the outdoor unit .

When using the exclusive grounding terminal 
(When the grounding terminal is already built on 
the house)

When using grounding of the switch board

Exclusive grounding terminal

Distributing board

DVM S HE_IM_DB68-05461A-08_EN.indd   85

2017-03-24   오후 1:38:41

Summary of Contents for AM080JXVHGH/EU



























































































































Reviews: