background image

 

IMPORTANT USER INFORMATION 

 

SAGEM RT3000 

 

File 

IMPORTANT USER INFORMATION.doc 

File saved 

08.05.04

 

File printed 

08.05.04 

State 

Freigabe 

Autor 

EDV/ORGA

 

!

 

 

IMPORTANT USER INFORMATION

 

FCC Part 15 

 

 

 

 

This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of 
the following measures: 

– 

Reorient or relocate the receiving antenna. 

– 

Increase the separation between the equipment and receiver. 

– 

Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected. 

Consult the dealer / installer or an experienced radio/TV 
technician for help. 

FCC part 15.19 

 

This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions:  

(1)  this device may not cause harmful interference, and  

(2)  this device must accept any interference received, including 

interference that may cause undesired operation. 

FCC part 15.21 

 

Modifications not expressly approved by this company could void 
the user's authority to operate the equipment. 

Installation by 
qualified 
personnel only 

  You may only use the SAGEM RT3000 with the antenna delivered 

together with the RT3000. 

The installation of the RT3000 and the antenna as well as 
servicing is to be performed by 

qualified technical personnel 

only. When servicing the antenna, or working at distances closer 
than those listed below, ensure the transmitter has been disabled. 

RFExposure 
mobil 

Keep distance ! 

Typically, the antenna connected to the transmitter is an omni-
directional antenna with 0dB gain. Using this antenna the total 
composite power in PCS mode is smaller than 1 watt ERP.  

The internal / external antennas used for this mobile transmitter 
must provide a separation 

distance of at least 20 cm from all 

persons

 and must not be co-located or operating in conjunction 

with any other antenna or transmitter." 

 

Summary of Contents for RT3000


























































































































Reviews: