Sagem RT3000 User Manual Download

Page: 100 / 121

Parameters in the file para.ini: advanced configuration

SAGEM RT3000

Datei 8115AD002-Total.doc

Datei gespeichert

24.04.04 13:23 von EDV/ORGA

Druckzeit 24.04.04,

18:17

Status Release

Section:

Meaning

Provider name

Permitted Values Factory Setting

Predefined Provider T-D1

PDP_CONTEXT

1,"IP","internet.t-
d1.de","0.0.0.0",0,0

Predefined Provider D2

PDP_CONTEXT

1,"IP","volume.d2gprs.d
e","0.0.0.0",0,0

Predefined Provider EPLUS

PDP_CONTEXT

1,"IP","internet.eplus.de"
,"0.0.0.0",0,0

Predefined Provider VIAG

PDP_CONTEXT

1,"IP","internet","0.0.0.0"
,0,0

New Provider

i.e. myGPRS

PDP_CONTEXT

PDP context as given by
the new provider.

16.22 CLIR on/off

Can be configured by SMS (see page 82)
Can be configured by FTP (see page 83)
Can be configured by DTMF (see page 80)

When you make a call your telephone number will be presented to the remote party
when this function is supported by the network. You can disable this function by setting
the following parameter:

CLIR=NO.

Section:

MOBILE_CONFIG

Meaning

Parameter

Permitted Values Factory Setting

Enable CLIR

CLIR

YES, NO

YES

16.23 PIN number

Can be configured by SMS (see page 82)
Can be configured by FTP (see page 83)
Can be configured by DTMF (see page 80)

The PIN number is stored in the parameter SIMPIN=<Pinnumber>.

Section:

MOBILE_CONFIG

Meaning

Parameter

Permitted Values Factroy Setting

SIM PIN

SIMPIN

empty

Summary of Contents for RT3000


























































































































Search results

Summary of Contents for RT3000

Reviews:

Related manuals for RT3000

Brands by name

Popular brands

Sagem RT3000, User Manual

Search results

Summary of Contents for RT3000

Reviews:

Related manuals for RT3000

Brands by name

Popular brands