background image

Configuration 

22 SAGEM 

RT3000 

 

 

Datei 8115AD002-Total.doc 

Datei gespeichert 

24.04.04 13:23 von EDV/ORGA

 

Druckzeit 24.04.04, 

18:17 

Status Release

 

8 Configuration 

Your SAGEM RT3000 is a sophisticated device with a wide range of modes of 
operation. You have to decide which operation modes are appropriate for your needs 
and then enable them by configuring the SAGEM RT3000. 

The configuration 
process 

Use a telephone connected to the 

Telephone

 port or the 

Fax/Modem/Phone

 port of the RT3000 to enter a special 

sequence (see below) just as you would dial a number. (The 
telephone must use tone (= DTMF) dialling.)  

The icons in the following descriptions mean: 

 

listen to the confirmation tone: 
 

a high pitched beep signals: OK 

 

a low frequency beep-beep signals: Wrong entry.  

You may have to wait 3 seconds before hearing the confirmation 
tone. 

 

lift up the handset. 

 

hook on the handset. 

ACCESS 

means: access code; by default it is 

000000

 

 

 

8.1 

Access code for DTMF configuration 

8.1.1 

Changing the DTMF access code 

The configuration of your SAGEM RT3000 is protected against unauthorised 
modification by an access code. The access code is part of each DTMF configuration 
code apart from the DTMF codes to configure call forwarding and call barring.  

The access code consists of 6 numeric digits. The default value is 

000000

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*5

 

OLDACC

 

023

 

NewACC

 

#

 

 

 

It means: 

OLDACC

 : old access code 

newACC

 : new access code

 

 

 

Summary of Contents for RT3000


























































































































Reviews: