Sagem RT3000 User Manual Download

Page: 87 / 121

Parameters in the file para.ini: advanced configuration

86 SAGEM

RT3000

Datei 8115AD002-Total.doc

Datei gespeichert

24.04.04 13:23 von EDV/ORGA

Druckzeit 24.04.04,

18:17

Status Release

Section:

DEVICE_ACCESS

Meaning Parameter

Permitted

Values

Factory
Setting

Activate SMS config

SMS_CONFIG

YES, NO

YES

PWD for config SMS

DEVICE_PASSWORD 000000 to 999999 000000

Activate CLIP check

SMS_CLIP=YES

YES, NO

YES

CLIP for Remote SMS

SERVICE_CLIP_0

100 digits

CLIP for Remote SMS

SERVICE_CLIP_1

100 digits

CLIP for Remote SMS

SERVICE_CLIP_2

100 digits

CLIP for Remote SMS

SERVICE_CLIP_3

100 digits

CLIP for Remote SMS

SERVICE_CLIP_4

100 digits

Section:

REMOTE_ACCESS

Meaning Parameter

Permitted

Values

Factory
Setting

CLIP for Remote CSD

SERVICE_CLIP_0

100 digits

CLIP for Remote CSD

SERVICE_CLIP_1

100 digits

CLIP for Remote CSD

SERVICE_CLIP_2

100 digits

CLIP for Remote CSD

SERVICE_CLIP_3

100 digits

CLIP for Remote CSD

SERVICE_CLIP_4

100 digits

Section:

SERVICE_IF

Meaning

Parameter

Permitted Values Factory Setting

See 15.3

USER

100 chars

service

See 15.3

PASSWORD

100 chars

service

16.3 Power-missing

SMS

Can be configured by SMS (see page 82)
Can be configured by FTP (see page 83)

If the mains power fails, the SAGEM RT3000 can send an SMS to a GSM telephone
number, which has to be pre-configured in the parameter file.

The function is activated by

[DEVICE_ACCESS]

POWER_REPORT=YES

POWER_REPORT_NR=<SMS Phone Number for Power Report>

Summary of Contents for RT3000


























































































































Search results

Summary of Contents for RT3000

Reviews:

Related manuals for RT3000

Brands by name

Popular brands

Sagem RT3000, User Manual

Search results

Summary of Contents for RT3000

Reviews:

Related manuals for RT3000

Brands by name

Popular brands