6
English
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
UK
Saw table
1
Locking bolts
2
Hex nuts
2
Extension support
1
Rip fence
1
Push stick
1
Operator's manual
1
assEMBly
unpacKinG
This product requires assembly.
■
Carefully lift the saw from the carton and place on a
level work surface.
warninG
Do not use this product if any parts on the Loose Part
List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer
installation. Use of a product that may have been
improperly assembled could result in serious personal
injury.
■
Inspect the tool carefully to make sure no
breakage or damage occurred during shipping.
notE:
This saw has been shipped with no blade
tension. Do not turn this saw on until blade tension has
been properly set.
■
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
■
If any parts are damaged or missing, please call your
service centre for assistance.
warninG
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
warninG
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
warninG
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
MountinG BanD saw to worKBEncH
If the band saw is to be used in a permanent location, the
band saw must be mounted to a firm supporting surface
such as a workbench. Four bolt holes have been provided
in the saw’s base for this purpose. Bolts (not included)
should be of sufficient length to accommodate the saw
base, lock washers (not included), hex nuts (not included),
and the thickness of the workbench. Tighten all four bolts
securely.
Carefully check the workbench after mounting to make
sure that no movement can occur during use. If any
tipping, sliding, or walking is noted, secure the workbench
to the floor before operating.
■
Place band saw on the workbench. Using the saw
base as a pattern, locate and mark the holes where
the band saw is to be mounted.
■
Drill holes through the workbench.
■
Place band saw on the workbench aligning holes in
the saw base with the holes drilled in the workbench.
■
Insert bolts (not included) and tighten securely
with lock washers and hex nuts (not included).
notE:
all bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of
the bench.
claMpinG BanD saw to worKBEncH
See Figure 4.
If the band saw is to be used as a portable tool, it is
recommended that you fasten it permanently to a mounting
board that can easily be clamped to a workbench or other
supporting surface. The mounting board should be of
sufficient size to avoid tipping of saw while in use. Any
good grade plywood or chipboard with a 19 mm (3/4”)
Thickness is recommended.
If lag bolts are used, make sure they are long enough to
go through holes in the saw base and material the saw is
being mounted to. If machine bolts are being used, make
sure bolts are long enough to go through holes in the saw
base, the material being mounted to, and the lock washers
Summary of Contents for RBS904
