manualshive.com logo in svg

RTI Piranha, Reference Manual, Page: 74 / 181

Share
Download
RTI Piranha Reference Manual Download Page 74

3. Description of the QABrowser
Installation of Palm OS Handheld Computers

Piranha & QABrowser Reference Manual

2014-06/5.5C

 

70

Installation of Palm OS Handheld Computers

3.10

Please note that if you purchased your Handheld Display (or Palm OS or Windows
mobile handheld computer) either directly from RTI or a RTI dealer, the QABrowser is
already installed and configured on the handheld. So if this is the case the only reason
for you to install the software on your PC is if: 

1. You need to update the QABrowser software on the handheld, using the QABrowser

Updater.

2. You have lost or uninstalled the QABrowser from the handheld.

If you have a Windows Mobile device, please see the 

QABrowser for Windows Mobile

User's Manual 

for instructions on how you install the QABrowser.

For the RTI Handheld Display or Palm OS  handheld computer, see the HTML help file
on your Product CD for details.

3.10.1

Updating QABrowser on the handheld

The QABrowser Updater helps you to install/update the QABrowser software on the
handheld computer. 

To update/install the QABrowser:

1. First install the QABrowser Setup as described in the previous chapter.

2. In the end of the installation process you will get the question if you want to run that

updater immediately. If you have your handheld computer and the cradle available
you can continue directly and step #4 below can be ignored. Perform step #6 and
answer "Yes".

3. Attach the HotSync cable.

4. Go to 

Start | RTI Electronics | QABrowser Updater | QAB Updater 

to start the

QABrowser Updater.

5. The QABrowser Updater

starts. If the PC is used with
more than one handheld
computer you are asked to
select user.

6. Select the user name of the

handheld computer and click
the 

OK

 button.

Summary of Contents for Piranha






















































































































































































Reviews:

No comments