RTI Piranha Reference Manual Download Page 36 | Manualshive

Page: 36 / 181

RTI Piranha Reference Manual Download Page 36

2. Description of the Piranha
Standards and Compliances

Piranha & QABrowser Reference Manual

2014-06/5.5C

32

2.5.4

FCC Certification

Piranhas of product version 3.1 and newer contains FCC certified transmitter module
(Bluetooth).

FCC ID R47F2M03GX

This device has been tested and found to comply with the limits for a Class-B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used according with the instruction manual,
may cause harmful interference to radio communication. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.

Maintenance

2.6

2.6.1

Updating the Piranha Firmware

All firmware that is controlling the function of the Piranha is stored in flash memory to
allow quick and easy update. The RTI Updater with the latest firmware is always
available free of charge on the RTI Electronics Web site at

http://www.rti.se

. To update

your Piranha you must first download the latest version and install it on a PC. The PC
needs to have an USB port.

You will need to have access to an administrative account to install the software.
To update the Piranha firmware (or bootloader):

1. First download the latest version of the RTI Updater Setup from RTI Electronics Web

site.

2. Unzip the file and run the file "RTI Updater Setup.exe" to install it on your PC. In the

end of the installation process you will get the question if you want to run that updater
immediately. If you have your Piranha available you can connect it as described in
step #3. Answer "Yes" and continue with step #6.

3. Connect the Piranha. Use the USB cable that came with your Piranha to connect your

Piranha to one of the USB ports on the PC. Power on the Piranha. Use the power
supply to ensure that no power failure occur during the update process. If you do not
have a power supply available, make sure you have fresh batteries in the Piranha.
You will get a notice about that.

4. Go to

Start Menu | RTI Electronics | RTI Updater

and select the RTI Updater.

«
...
34
35
36
37
38
...
»

Summary of Contents for Piranha






















































































































































































Reviews:

No comments