manualshive.com logo in svg

RTI Piranha, Reference Manual, Page: 110 / 181

Share
Download
RTI Piranha Reference Manual Download Page 110

5. Measurements with the Piranha System
Fluoroscopy and Pulsed Fluoroscopy 

Piranha & QABrowser Reference Manual

2014-06/5.5C

 

106

9. Start the fluoroscopy. A little triangle is displayed, indicating that the Piranha has

detected the radiation.

10. The figure to the left shows the real-time

display during fluoroscopy. The image
intensifier input dose rate is measured and
the display is updated approximately every
four seconds. Tap 

Hold

 to "freeze" the

currently shown value in the display. The
waveform is also acquired when Hold is
activated.

11. Release hold by tapping 

Hold

 again.

12. Stop the fluoroscopy.

13. Read the values.

5.4.2

kVp and Dose Rate

Use the same procedure as for the image intensifier input dose rate measurement but
select 

All...

 

parameters instead.

    

1. The first screen shows how the continuous updated display looks like. The little black

arrow indicates that the radiation is detected and the display is updating every four
seconds.

2. The second screen shows that the Piranha has detected that the fluoroscopy have

stopped by flashing the logo and then freeze the values. Note that the last registered
kV value may be lower than the one measured during the exposure. The last display
update may occur when the exposure is switched off and the kVp is captured on the
"falling edge". The dose rate shown after the logo flashes is the average dose rate of
the entire exposure.

Summary of Contents for Piranha






















































































































































































Reviews:

No comments