manualshive.com logo in svg

RTI Piranha, Reference Manual, Page: 3 / 181

Share
Download
RTI Piranha Reference Manual Download Page 3

NOTICE

Palm, palmOne, and TUNGSTEN are trademarks of PalmOne, Inc.

HotSync and Graffiti are trademarks of ACCESS CO., LTD

Microsoft, Windows, Win32, Windows XP, 2003, Vista, 7, and 8 are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries.

BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., USA.

 

Notice

RTI Electronics Inc.
33 Jacksonville Road, Bldg. 1,
Towaco, NJ 07082,
USA

Phone: 800-222-7537 (Toll free)
            Int. +1-973-439-0242
Fax:     Int. +1-973-439-0248

E-mail
Sales: [email protected]
Support: [email protected]
Service: [email protected]

Web site: http://www.rti.se

Contact Information - 
United States

RTI Electronics AB reserves all rights to make changes in the Piranha, the
QABrowser, and the information in this document without prior notice.
RTI Electronics AB assumes no responsibility for any errors or consequential
damages that may result from the use or misinterpretation of any information
contained in this document.

Copyright © 2001-2014 by RTI Electronics AB. All rights reserved.
Content of this document may not be reproduced for any other purpose than
supporting the use of the product without prior permission from RTI Electronics
AB.

RTI Electronics AB
Flöjelbergsgatan 8 C
SE-431 37 MÖLNDAL
Sweden

Phone: Int. +46 31 7463600

Fax:     Int. +46 31 270573

E-mail
Sales: [email protected]
Support: [email protected]
Service: [email protected]

Web site: http://www.rti.se

Contact Information - 
World-Wide

Piranha & QABrowser Reference Manual

2014-06/5.5C

III

Summary of Contents for Piranha






















































































































































































Reviews:

No comments