manualshive.com logo in svg

RTI Piranha, Reference Manual, Page: 118 / 181

Share
Download
RTI Piranha Reference Manual Download Page 118

5. Measurements with the Piranha System
Mammography

Piranha & QABrowser Reference Manual

2014-06/5.5C

 

114

have probably selected a set kV value higher than the actual measuring range. Another
reason may be that you have selected wrong radiation quality compared to what the
generator is set to.

To be able to trust the kVp reading it is always very important to make the 

Position Check

 to verify that the whole detector area is uniformly irradiated.

The 

Position Check

 is normally started automatically every time you

change R

adiation Quality

, but please make sure to do a 

Position Check

every time the Piranha is repositioned.

The kV and radiation waveform is always stored together with the RTD values and can
be displayed by tapping the 

Wave

 button. The kVp calibration for Piranha is made

without the compression paddle in place.

The purpose of dose measurement is often to determine the ESAK, 

Entrance Surface

Air Kerma

 (or ESE, 

Entrance Skin Exposure

).

It is recommended to perform dose measurements according to a mammography
protocol. One is the "European Protocol on dosimetry in mammography EUR 16263 EN
from the European commission". Chapter 3 in this protocol describes in detail the
determination of AGD, 

Average Glandular Dose

 (or MGD, 

Mean Glandular Dose

). The

AGD is derived from measurements of the HVL and of the ESAK. Make use of tabulated
conversion factors from ESAK to AGD. See 

Average Glandular Dose, AGD (MGD)

.

5.5.2

Setting Up the Piranha for Mammography

    

123

Summary of Contents for Piranha






















































































































































































Reviews:

No comments