RTI Piranha Reference Manual Download Page 10 | Manualshive

Page: 10 / 181

RTI Piranha Reference Manual Download Page 10

1. Introduction
Introduction to the Piranha

Piranha & QABrowser Reference Manual

2014-06/5.5C

6

This manual describes the Piranha and the QABrowser. The PC software, Ocean, is
described in a separate manual.

The Piranha system's main features are:

Very easy and intuitive to use
Accurate
Active Compensation - No manual corrections are needed
Measures on all modalities with one detector
Specially designed measuring modes for pulsed waveforms
Compact
QABrowser or Ocean is used for control and data processing
Waveform analyser
USB and Bluetooth interface
Free upgrade of firmware
New and unique design

Free upgrades of the firmware (the software resident in the cabinet and measuring
modules) are available on RTI Electronics Web site at

http://www.rti.se

.

If you have questions, comments, or feel that some functionality is missing, you are
welcome to contact us at RTI Electronics at

[email protected]

. You can of course also call or

send a fax (see notice section for details).

PC Requirements

1.3

To run the RTI Updater, the QABrowser Updater, and Ocean the following is required:

Minimum requirements

Windows XP, 2003, Vista, 7/8 32-bit, or 7/8 64-bit.
Pentium class 300 MHz, 64 MB RAM (24 MB free), 60 MB of HD

1

USB port
Display and graphics card with at least 800×600 resolution

Recommended requirements

Windows 7/8 32-bit or 8 64-bit
Pentium class 500 MHz, 128 MB RAM (32 MB free), 100 MB HD
USB port
CD/DVD-ROM for installation
Internet connection for updates (Recommended)

1

: Virtual memory and available hard drive space. Microsoft recommends that you have at least 20 % of your

total HD space free for virtual memory.

Palm OS Computer Requirements

1.4

To run the QABrowser the following is required:

Minimum requirements

PalmOS v5.0 or higher
16 MB of memory
Colour screen with a resolution of 320×320 pixels
Palm connection: Bluetooth wireless

Recommended requirements

«
...
8
9
10
11
12
...
»

Summary of Contents for Piranha






















































































































































































Reviews:

No comments