manualshive.com logo in svg

RTI Piranha, Reference Manual, Page: 37 / 181

Share
Download
RTI Piranha Reference Manual Download Page 37

2. Description of the Piranha

Maintenance

2014-06/5.5C

 

33

Piranha & QABrowser Reference Manual

5. The RTI Updater starts and locates the Piranha automatically if it is connected to an

USB port. 

6. If the Piranha is found, the window in the figure above is shown. The different

modules are checked and after a while the start button is enabled. Click 

Start

. If the

Piranha cannot be found, a message with suggested solutions is shown.

7. The updating process starts. The RTI Updater checks the current versions and

compares with the update. Modules with old firmware are automatically updated.

8. Note that storing the new firmware in the flash memory may take several minutes for

each module. The RTI Updater will indicate which modules have been updated.

9. Power off the Piranha and disconnect the serial cable when the program indicates

that everything is OK.

Summary of Contents for Piranha






















































































































































































Reviews:

No comments