RTI Piranha Reference Manual Download Page 112

Page: 112 / 181

5. Measurements with the Piranha System
Fluoroscopy and Pulsed Fluoroscopy

Piranha & QABrowser Reference Manual

2014-06/5.5C

108

5.4.3

HVL, Total Filtration, and Quick-HVL

HVL can be measured in a similar way as described for the radiography measurements
but the dose rate value is used instead.

1. Select

Dose rate

2. Tap

Appl

and select

HVL

3. Use the

Hold

button to store a reading

and move to next line when the displayed
value is stable.

Total Filtration and Quick-HVL

The total filtration is measured continuously when the Piranha is used under
fluoroscopy. The following pictures illustrates this excellent feature for the Piranha and
the Internal detector (shown for Barracuda MPD):

The fluoro is started and the total filtration is estimated and automatically displayed
during two seconds.

Summary of Contents for Piranha






















































































































































































Search results

Summary of Contents for Piranha

Reviews:

RTI Piranha, Reference Manual, Page: 112 / 181

Search results

Summary of Contents for Piranha

Reviews: