Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download

Page: 51 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

4.44

Skid Plate

Assemble the 4 rubber
bushes in the bottom
mounting holes of the
Skid plate and locate 4
damper bushes on the
rubber bushes.

Position the Skid plate
under the cradle frame
and align the mounting
holes. Ensure the
damper bushes do not
fall off.

Assemble

4 Flanged

Hex Bolts M6 X1 X 35

the bottom of the Skid
plate.

Assemble

2 Flanged

Hex Bolts, M6 X 1 X 14

at the front of the skid
plate.

Tighten

all the 6 bolts

evenly and diagonally.

Flanged Hex Screw: M6

Socket Spanner: 10mm

Torque: 10Nm (0.1 Kg.M)

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands