manualshive.com logo in svg

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

The Royal Enfield HIMALAYAN EURO IV 2017 is a rugged and reliable adventure motorcycle designed for off-road enthusiasts. To ensure the best performance and longevity of your bike, it's essential to have the Service Manual. Download this comprehensive manual for free from our website, providing step-by-step instructions to maintain and repair your HIMALAYAN.

Share
Download
background image

226

ROYAL ENFIELD    HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

INSPECTION

A) PHASE TO PHASE RESISTANCE CHECK

1.

Phase to phase resistance of the magneto shall be checked by setting multimeter in resistance mode.

2.

Phase to Phase resistance – 1.5 +/-15% (0.59 to 0.79 ohms)

3.

If the resistance deviates from the spec, then cover shall be opened and checked if stator coil has burnt. If stator
coil is burnt then replace the magneto.

If multimeter shows open during resistance check, the coil has got cut or short with the core and magneto has to be
replaced.

B) INSULATION TEST

1.

For checking the insulation strength, keep the multimeter in continuity mode and check continuity between any
3 phase terminals and engine body. If there is a body short(insulation failure), multimeter will indicate 0ohms (or
resistance value ~ 50 ohms) with a beep sound.

If insulation failure is observed, failed magneto to be replaced with new magneto.

 2. During visual inspection, if stator coil has burnt, magneto shall be replaced with new magneto.

FFLYWHEEL MAGNETO

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Reviews:

No comments

Related manuals for HIMALAYAN EURO IV 2017

B-PWR PAFB-1C Instruction Manual preview
PAFB-1C
Brand: B-PWR Pages: 12
R&G ECC0364R Fitting Instructions Manual preview
ECC0364R
Brand: R&G Pages: 6
KTM Super Adventure 2016 Setup Instructions preview
Super Adventure 2016
Brand: KTM Pages: 25
rizoma BS174 User Manual preview
BS174
Brand: rizoma Pages: 10
KTM Power Parts 77202923000 Information preview
77202923000
Brand: KTM Power Parts Pages: 7
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet preview
MILWAUKEE-EIGHT 5833
Brand: JIMS Pages: 10
ALPENHEAT fire PANTLINER AJ6 Manual preview
fire PANTLINER AJ6
Brand: ALPENHEAT Pages: 26
Ducati Multistrada 620 Owner'S Manual preview
Multistrada 620
Brand: Ducati Pages: 382
SUOMY MX SPEED Manual preview
MX SPEED
Brand: SUOMY Pages: 26
Wunderlich 31000-301 Fitting Instruction preview
31000-301
Brand: Wunderlich Pages: 4
Taurus Z9PRO Assembly And Operating Instructions Manual preview
Z9PRO
Brand: Taurus Pages: 48
Bike Shield Junior Small Assembly Instruction preview
Junior Small
Brand: Bike Shield Pages: 4
X-PRO XB27B-125 Manual preview
XB27B-125
Brand: X-PRO Pages: 3
X-PRO Marvel A09 Quick Manual preview
Marvel A09
Brand: X-PRO Pages: 3
APRILIA MANA 850 ABS Manual preview
MANA 850 ABS
Brand: APRILIA Pages: 197
Yamaha Vmax VMX12N Owner'S Manual preview
Vmax VMX12N
Brand: Yamaha Pages: 93
Yamaha VMAX VMX12S Owner'S Manual preview
VMAX VMX12S
Brand: Yamaha Pages: 100
Yamaha VMAX VMX12W1 Owner'S Manual preview
VMAX VMX12W1
Brand: Yamaha Pages: 102

Brands by name

Popular brands

Load more brands