manualshive.com logo in svg

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

The Royal Enfield HIMALAYAN EURO IV 2017 is a rugged and reliable adventure motorcycle designed for off-road enthusiasts. To ensure the best performance and longevity of your bike, it's essential to have the Service Manual. Download this comprehensive manual for free from our website, providing step-by-step instructions to maintain and repair your HIMALAYAN.

Share
Download
background image

126

ROYAL ENFIELD    HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

12.16

R

Rear Wheel
Reassembly

Ensure the cush rubbers
are in place in the wheel
hub.

Insert the wheel
assembly between the
swing arms and position
the cush rubbers on the
rear sprocket lugs
correctly.

Remove the spacer
between the brake pads
and locate the caliper
such that the brake disc
is between the brake
pads.

Locate the caliper
bracket slot on the lug in
the swing arm.

Position the respective
spacers on the left and
right side of the wheel
hub.

Ensure the axle
mounting hole in the
swing arm, wheel hub
and caliper bracket are
aligned.

Insert the wheel axle
from the left side of the
swing arm and gently tap
it in.

S.

No.

CAUTION:

Do not force the
spindle through as it will
cause damage to the
threaded end.

Ensure correct chain
tension and rear wheel
alignment with front
wheel by adjusting the
adjusters on both left
and right side of swing
arm.

Assemble washer and
wheel axle nut on right
side and tighten to
correct torque.

Fix the brake hose pipe
in swing arm clips
properly.

CAUTION:

Please ensure the
brake hose is correctly
positioned on the clips,
without any twist,
sharp kinks or damage
as it will seriously affect
the performance of the
rear brake.

Check rear brake for
effectiveness and
correct functioning
before using the
motorcycle.

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Reviews:

No comments

Related manuals for HIMALAYAN EURO IV 2017

N-Com R Series User Instructions And Safety preview
R Series
Brand: N-Com Pages: 28
Can-Am DS250 Instructions Manual preview
DS250
Brand: Can-Am Pages: 16
Can-Am OUTLANDER Operator'S Manual preview
OUTLANDER
Brand: Can-Am Pages: 254
Yamaha MX360 Supplementary Service Manual preview
MX360
Brand: Yamaha Pages: 32
hepco & becker TRIUMPH Bonneville T 120 Quick Start Manual preview
TRIUMPH Bonneville T 120
Brand: hepco & becker Pages: 4
KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Brand: KTM Pages: 163
APRILIA SPORTCITY CUBE 125 Manual preview
SPORTCITY CUBE 125
Brand: APRILIA Pages: 157
National Cycle ZTechnik VStream Z2392 Installation Instructions preview
ZTechnik VStream Z2392
Brand: National Cycle Pages: 2
Artotic SUN9B User Manual preview
SUN9B
Brand: Artotic Pages: 9
PIAGGIO VESPA GTS FL2 Instruction Manual preview
VESPA GTS FL2
Brand: PIAGGIO Pages: 8
Yamaha TT-R90(V) Owner'S Service Manual preview
TT-R90(V)
Brand: Yamaha Pages: 390
Yamaha TTR125LM Owner'S Service Manual preview
TTR125LM
Brand: Yamaha Pages: 468
Yamaha TT-R90(T) Owner'S Service Manual preview
TT-R90(T)
Brand: Yamaha Pages: 364
Yamaha TZ250M1 Owner'S Service Manual preview
TZ250M1
Brand: Yamaha Pages: 287
Yamaha TW200P Owner'S Manual preview
TW200P
Brand: Yamaha Pages: 109
hepco & becker 504980 00 05 Quick Manual preview
504980 00 05
Brand: hepco & becker Pages: 2
Royal Enfield SCRAM 411 2021 Owner'S Manual preview
SCRAM 411 2021
Brand: Royal Enfield Pages: 110
hepco & becker 6002524 00 01 Assembling Instructions preview
6002524 00 01
Brand: hepco & becker Pages: 9

Brands by name

Popular brands

Load more brands